R. KAMBLI

Looking for a Challenging Career with a reputed organization, where in I have a good scope for broadening and enhancing my current skills and gain Knowledge.

• Fluency in English.
• Good analytical and managing skills.

• 1) Role & Responsibilities – Marine, Berth & Subsea Areas
• Conduct off-stream and on-stream RBI-inspection on the off-shore top side facilities and plant stationary equipment including pressure vessels, heat exchangers, drums, tanks, PSVs and piping systems according to Company established policies and procedures and issues inspection reports.
• Conduct welding Inspection (Internal and external) for primary and secondary structure repair works.
• Inspects plant stationary equipment by entering into vessels, during shutdowns, to check condition of equipment. Includes observations on cracks, pits, thinning and any other pattern of erosion, corrosion and other interior failure.
• Checks condition of safety relief valves, and report findings to supervisor. Witnesses pressure setting before and after repair and during any re-calibration campaign, as assigned. Prepares report, schedules testing frequency as per policy, enters inspection data in TruQc, computerized system, raises recommendation based on valve condition and follow up.
• Witness hydrostatic tests and pneumatic tests on pressure equipment, and pipelines as per Company policy.
• Inspects maintenance and capital project works being carried out in the plant, to ensure that specified maintenance practices and procedures are followed for welding, installation and fabrication as per policy and in compliance with international fabrication codes and standard.
• Supervises and co-ordinates the NDT team whenever required.
• Ensures proper maintenance of inspection reports and records. Maintains various records in the computerized systems, updating inspection test results and other data in specialized inspection software system (Credo, TruQc, and Pestra).
• 2) Role & Responsibilities – Static Equipment
• Familiar in reading equipment strategy and able to understand risk categorization assigned for piping circuit or an equipment.
• Daily Dealing with Piping in-service inspection items like, external Atmospheric corrosion, CUI (Corrosion under insulation), CAPS (corrosion at pipe supports), dead legs, mix points, Injection points, injection quills, and other damaged mechanisms involved in the oil and gas refineries.
• Involved in in-service inspection activities.
• Dealing with Inspection of Pressured Equipment’s Such as heat Exchangers, Air fin exchangers: Pre, Post & Hydrotest Inspections
• External Visual Inspection, inspection during and after Bundle pulling, tube bundle inspection, shell internal inspection, after hydro jetting follow up for any NDE like IRIS/RFET (if applicable), hydro test witness, total flange assurance and final documentation.
• Columns, Towers: Pre, Post, Tray Assembly, Collectors & Distributor Inspection.
• External visual inspection, internal Tray condition, new tray installation witness, checking the orientation of trays, Random checking the torque value of bolt nuts, Chimney weld visual, PT & Leak test, new nozzle installation, hydro test witness, Total flange Assurance and final documentation.
• Drums, Vessels: Pre, Post & Demister Pad Inspection
• External visual inspection, internal cleaning witness, Demister Visual Inspection, Shell Internal Inspection, hydro testing witness, Total flange assurance and final documentation.
• Heaters, Boilers: Pre, Post, Burner & Lining Inspection
• External visual inspection, Internal inspection (both radiant and economizer sections), refractory inspection, Total flange Assurance & final documentation, Decoking inspection ILI (In line inspection-for thickness verification & to identify carburization), thermography inspection to identify the hot spots.
• Reactors: External & Internal VI, Catalyst loading (density calculation witness).
• Drone inspection for visual/ thermography (stack, ducts, heaters, flares-internally & externally).
• 3) Role & Responsibilities – Piping
• Performing structural & pipeline Inspection during fabrication & assembly and ensuring that built as per drawing and meet the requirements of standard. Involved various Project such as Aromatics, Slop Oil, and Mogas & ADO.
• Performing in service External Visual inspection & Risk Based Inspection for Pipelines to do Risk Assessment & Find Out the Relevant damage Mechanism as per Code & Standard.
• Performing fireproof inspection (Corrosion Under Fireproof) On Tank Column & Pipe Rack as Per Standard.
• Perform visual Inspection for Underground pipelines to do risk Ass & Mitigation.
• Planning repair Work, Partial Renew, Patch back on structure, fender, pipe as per Repair Procedure.
• Performing inspection for locating hot spot of pipeline and valves for high temperature embrittlement failure of stainless steel (ferritic) & graphitization of carbon steels.
• Performing visual inspection & CUI inspection for Pipelines and valves at CML.
• Witnessing UT corrosion mapping & thickness verification at TML and submit report to plant Engineer.
• Performing visual inspection of insulation for damages and note down the susceptible location for corrosion under insulation (CUI)
• Performing line check prior to hydrotest and punch list preparation. Performing material verification for pipe, plate, I beam, flange, Elbow and verifying the mill certificate and DNV3.1 or3.2 certificate.
• Performing the inspection for joint configuration as per WPS & drawings, calibration certification for equipment’s, welding consumable (storage & requirements), welder qualification, condition of base metal & consumable preheating before welding
• Preheating before welding.
• Witnessing and verifying the NDT activities such as RT, UT & PAUT, MPI, PT, DFT & Holiday test as per ITP
• Radiographic Film interpretation for weld joints as per code as per ASME B31.3 and SEC V & VIII & review the Profile radiography to find internal corrosion on pipelines.
• Witnessing and monitoring PWHT, HYDRO TEST, and LEAK TESTING (VACCUM BOX) as per procedure & specification.
• Reviewing PWHT Charts, Witnessing of Hardness Test & PMI.
• Preparation and verifying the final inspection report of structure and piping and submit to report to Engineer with all relevant documents on time.

• NABHA thermal power plant Rajpura Punjab (UT TECHNICIAN) DEC2016 -FEB2017
• AMBUJA cement pvt.ltd. Himachal Pradesh (UT & MT) APRIL2017 - JUNE2017
• NUCLEAR power plant tarapur Mumbai. (UT & PT) JUNE2019 - SEPT2019
• SCP S02P(ExxonMobil) Shutdown on API inspector on Vessel team (Feb2023 to April2023)
• SAR2 (ExxonMobil) Shutdown on API inspector on Vessel & Fired heater team (May2023 to July2023)
• Arkema symphony plant Shutdown on API inspector on Vessel & Fired heater team (June2024 to August2024)
• Neste Oil Plant Pit stop as API inspector on Vessel’s & Piping (Oct2024 to Dec2024)

• General visual inspection and Corrosion under pipe support inspection .and making report and Clint review.
• Mechanical work using by rope access.
• Caustic line insulation removal & visual inspection and photo taking and UTG measurement for anchor point.
• Support I.R.M. work at refinery and chemical plants industry approved rope access methods and skills.
• Assist in Radiographic Testing (RT) works using rope access.
• Carrying out Maintenance Assessment and On-Stream Inspection utilizing nondestructive testing (NDT) such as Visual and Ultrasonic on onshore facilities to ascertain their integrities and recommend necessary action are taken as per required codes, standards and specification.
• Passed ExxonMobil qualification test ‘Coated and Uncoated’ in2017
• Passed shell petroleum qualification test ‘Coated and Uncoated’ and piping evaluation test in2019.
• Ultrasonic corrosion monitoring of defined process piping to detect internal wall loss.
• UT thickness survey of tanks & pressure vessels
• Assisting with Verkade inspection.
• Complying with Permit to work systems & report writing with MS- Office word & excel

• Carry over industrial power cables pulling using by rope access methods.
• Installing new cable tray on pipe rack
• Changing stack overhead which is100m height.
• Drenching works on take
• Changing rupture pipes on tank
• Lockering '2' pipe
• - To install new pipe connection on the pipe rack using Lockering machine
• Insulation removal /put back.
• - For further inspection we remove insulation on which is needed to be inspection.
• - Once completed inspection we put back new insulation along with cladding
• Painting works on tank

• Good Leadership quality as I was represented as class representative in my school days.
• “THIS IS JUST A BEND NOT AN END” encouraging quotes for my responsibility and for my leadership quality.