Jirapong Pongpaew
Process Engineering Manager
Summary
Obtain a position of Process Engineering Manager
Overview
20
20
years of professional experience
3941
3941
years of post-secondary education
Work History
Process Engineer Assistance Manager
BASF Chemcat (Thailand) Limited
10.2013 - Current
- In 2013, Support installation new machine of MCC6 Robot, Belt Pre-Dryer and Calciner that transfers from BCSC to increase production capacity of BCTL, machines validation for current customer and new customer for new line and committed customer audit to approve mass production for new production line.
- Start implement MCC Mode coating for MCC6 coater to reduce blowout slurry and cleaning water in production process.
- 2014, Implement lean manufacturing with SMED to reduce change over time for MCC6 can reduce change over time to 20 minutes and win Asian lean manufacturing award 2014.
- 2015, Implement PGM visibility program for BCTL follow high level procedure (HLP) of slurry trend and coating lot close out, until present still use this program for Gain/Loss calculation.
- 2016, Cooperate with APQP team to launch new model project since start event technical transfers until it can mass production.
- 2017, support installation new machine of MCC6 Robot, Belt Pre-Dryer and Calciner for new site (THEP), validation machines for each customer, create machine check sheet, work instruction, site procedure and all Support documents that concern production for new site, then committed customer audit to approve mass production for new site.
- 2018, Support coating production, new model, technical transfers or trial for new model, validation machine, support customer audit for new model, issue work instruction, site procedure and check sheet and training operators, coating line improvement such as scrap reduction, productivity improvement, internal audit for IATF 16949 and ISO 14001, Key input production master recipe to SAP system and responsible for RC system by to be a MOC (Management of change) chairman to manage all change in BCTL.
- 2019, Create Mass Balance (MB) Program with VBA to release slurry with MB and WG target calculation program with deviation between MB and XRF
- 2020, Complete RTC (Ready to coat) Project, develop slurry property (Viscosity and Solid content) to be ready for coating
- 2021, Start Targeting project reduce target of coating lower than nominal for cost saving, improve Cpk of coating process to higher than 2.0 with coating process optimization, machine modification and Slurry Rheology study (Slurry behavior study) and slurry property improvement
- 2022, Complete installation MCY3 Motorcycle coater and pass AMO audit
- 2023, MCY3 Cpk improvement by change coating slurry charging method from peristaltic pump to filling machine can improve Cpk from 0.8 to 2.5
- 2024-present Cross Model and Cross Technology, create PGM compensate calculation sheet for mix slurry in the same technology or different technology to increasing consumption of remain and wash water
Production Engineer
Visteon (Thailand) Limited
01.2013 - 10.2013
- Interior Assembly Team (IAT), Control assembly production, install POKA-YOKE, assembly line improvement, improve OEE of assembly line, respond customer claim, respond for customer audit, line improvement follow 4M change from customer request in an interior assembly process, Door trim, Front panel assembly of GMT700 (Chevrolet Trailblazer), GMT300 (Chevrolet Sonic), T5 (Ford everest, Ranger) and L42L (Nissan Teana)
Technical Staff (Process Engineer)
Bridgestone Tire Manufacturing (Thailand) Limited
04.2005 - 04.2012
- Calender process (Inner Liner), reduce liner air defect (air inside inner liner) and improve calender process with cold process install and validation cold inner liner machine.
- Cutting process Ply coating process, reduce ply open scrap by change the wire roll type to the same type of roll, reduce belt cutting scrap by reuse edge of cutting belt by joint the cutting belt together.
- Curing process, Install new curing process 48 machine, apply new chemical to use with curing mold this project can reduce one production process (inner paste spraying process), trial new technology of tire with confirm curing efficiency by cutting curing tire and check blow point to reduce curing cycle time, reduce scrap from curing process, improve curing productivity by change curing safety factor and confirm with blowout test.
Education
High School Diploma -
Udornpittayanukul School
Udornthani Thailand 04.2001 -
Bachelor of Engineering - Chemical Engineering
Khonkean University
Master of Science - Industrial management
King Mongkut's Institute of Technology Ladkrabang
Timeline
Process Engineer Assistance Manager
BASF Chemcat (Thailand) Limited
10.2013 - Current
Production Engineer
Visteon (Thailand) Limited
01.2013 - 10.2013
Technical Staff (Process Engineer)
Bridgestone Tire Manufacturing (Thailand) Limited
04.2005 - 04.2012
High School Diploma -
Udornpittayanukul School
04.2001 -
Bachelor of Engineering - Chemical Engineering
Khonkean University
Master of Science - Industrial management
King Mongkut's Institute of Technology Ladkrabang
Training And Skills
Complete training program on IATF 16949:2016 Internal Automotive Task Force and ISO 19011:2019 Internal Audit for IATF16949:2016, Complete training program on ISO 14001:2015 Environmental Management system and ISO 19011:2019 Internal Audit for ISO 14001:2015, Complete training program on APQP Core tools, Statistical Process Control (SPC), Measurement System Analysis (MSA) and Failure Mode and Effect Analysis (FMEA), Thai, Native, English, TOEIC score 490, Microsoft Office (Word, PowerPoint, Excel), Basic programming by Excel, AutoCAD, Sketchup
Personal Information
Date of Birth: 08/23/82
Born : Udornthani, Thailand
Training And Skills
Complete training program on IATF 16949:2016 Internal Automotive Task Force and ISO 19011:2019 Internal Audit for IATF16949:2016, Complete training program on ISO 14001:2015 Environmental Management system and ISO 19011:2019 Internal Audit for ISO 14001:2015, Complete training program on APQP Core tools, Statistical Process Control (SPC), Measurement System Analysis (MSA) and Failure Mode and Effect Analysis (FMEA), Thai, Native, English, TOEIC score 490, Microsoft Office (Word, PowerPoint, Excel), Basic programming by Excel, AutoCAD, Sketchup
Similar Profiles
Ashebir AsratAshebir Asrat
IT officer at LIMITEDIT officer at LIMITED
Gamolmat MokharatGamolmat Mokharat
Accounting Intern at ThailandAccounting Intern at Thailand
Aung Khant KyawAung Khant Kyaw
Office Assistant at ThailandOffice Assistant at Thailand
Tabish Ul HaqueTabish Ul Haque
Assistance Manager-Inventory (D&L) & Process Owner at DSV Solutions Pvt. LtdAssistance Manager-Inventory (D&L) & Process Owner at DSV Solutions Pvt. Ltd
Abel ShehabAbel Shehab
Process Assistance at Amazon.com IncProcess Assistance at Amazon.com Inc