Challenging and motivating career with an esteemed organization to enhance knowledge and to achieve excellent quality life style through continuous improvement to learn and apply new technologies, Valivalam Desikar Polytechnic College, Tamil Nadu, INDIA, D.E.C.E. (Diploma in Electronics and communication Engineering), 64%, 2010 - 2013, T.G.N.M Higher secondary School, Tamil Nadu, INDIA, SSLC, 72.2%, 2009 - 2010, Plant Electrical Instrumentation Pte Ltd., (joint venture with Yokogawa & PEC), Senior Instrument Technician, Exxon Mobil Chemical Asia Pte Ltd, July’16– at present, Involved in the Preventive maintenance and Safety critical priority maintenance for field instruments and TA activities., Calibration and troubleshooting of field Instruments, such as Pressure, Level, Temperature and Flow. Control valve, vibration like radial axial and seismic, probes, etc., Calibration and troubleshooting of area gas detectors such as LEL, CO, CL2,H2S., Involved in the pre-loop check and final loop check from control room DCS to field and vice versa., Trouble shooting of Electrical plant lighting, panels, receptacles, Electrical process heat tracing system., Performing the monthly and yearly preventive maintenance for motor, VFDs, MOVs and cathodic protection., Involved in the PSSR walkabout with contractor for newly installed instruments at site., Plant fire alarms system maintenance and troubleshooting, Following Exxon Safety Standards with Responsibilities., JINDAL THERMAL POWER PLANT (4X600 MW), under CHEMIN C&I PVT. LTD, Chhattisgarh, India, Instrument Technician, Sep’15 to June’16, Good knowledge about P&I Drawings, Termination detail drawings for control panels, JB’s and field instrument side and instrument Hookup Drawings., Duties involved in bench calibration and installation of all instruments on site. This includes instrument tubing, termination of cables of all instrument’s installation., Calibration & commissioning of Instruments such as Smart and conventional field Transmitters (PIT, LIT, FIT) Thermocouple, RTD, Pressure & DP Switches & Limit Switches, All types of Gauges., Testing and Commissioning of final control elements such as Control Valves, Pneumatic Dampers, ON-OFF actuators., Ensure company safety rules and quality procedures are fully respected during all stages of work., Good inter-personal skills, Communication and willingness to learn., Self-motivated, independent and initiative. Ability to work as a team., Good leadership and customer focus, attention to details, accurate and thorough, and are able to lead the team members., Workplace Safety and Health in Process Plant (Singapore), Workplace Safety and Health in Construction Sites (Singapore), Industrial Instrumentation and Measurement in Chemin Controls (INDIA), AUTO CAD 2D ELECTRICAL (INDIA), In CCR one of the dump valve control room unable to get feedback due to that the whole reactor went to trip. I found there is the target magnet is miss aligned with feedback switch then, I adjusted and prevent the reactor from trip., Polymer reactor one of the control Flow serve on off valve unable to stroke 100% full open. I found the limit switch holding the stem to move 100% separate the limit switch serviced the switch then installed back at original position and performed manual stroke and informed control room to stroke its working fine then, I handed over to operation., During plant startup time, operation reported one of the flow DP transmitter always shows bad PV at DCS also it is a HCP pay meter, I attend that issue, found Transmitter side no issue, loop side has the issue. And then from local JB to marshaling cabinet did continuity check and megger check, then found cable was shorted somewhere in between JB to Marshaling Cabinet, it’s a 32 pair Cable there is 4 Spare be in available at JB and Then I informed my supervisor to Raise MOC, once got approval use the spare cable arranged the cable to correct TB and update the loop drawing and performed PSSR, tie in the cable in particular TB of the transmitter. Then verified HART loop check, Transmitter 5 point check then handed over to Operation., Knowledge in LPS -Exxon Mobil Safety Standard, Knowledge in applying LPSA for entire Job, Actively Participated in Safety Programs TBM & Submitting NLI, CAT 3 T1 Best Practice Permit Applicant -Exxon Mobil, Knowledge in SAP -Updating Work Order and Notification Closure, Electrical safe working practice – Exxon Mobil, CPR + AED Trained, Parker autoclave trained
